Updated November 2026

A diy solar backup generator lets you keep essential appliances running during an outage by pairing solar panels with a battery and an inverter. This guide walks you through estimating your daily energy use, sizing the battery and panels, and choosing the parts that make the system work. The goal is a setup that covers your fridge, a CPAP machine or a sump pump for as long as you need it.

Step 1: Calculate Your Essential Watt-Hours

Start with the appliances you truly need during an outage. Find each device’s wattage on its label, then estimate how many hours per day it runs. Multiply watts by hours to get watt-hours (Wh) per day.

Shopping for one? See our guide: 5 Best DIY Solar Generators for Home Backup Picks Compared (2026).

  • Refrigerator: often 100 to 200 Wh per day, since the compressor cycles on and off. Check the energy guide label for kWh per year and divide by 365.
  • CPAP machine: commonly 30 to 60 W while running, around 8 hours a night, or roughly 240 to 480 Wh.
  • Sump pump: a 1/3 HP pump draws several hundred watts while running, but only runs briefly. Estimate actual run time during a storm.
  • LED lights and phone charging: usually a small share of the total, but include them.

Add the daily totals, then add a 20 percent buffer for inverter losses and cloudy days.

Step 2: Size the Battery Bank

Your battery capacity should cover your daily total for the number of backup days you want. For example, 1,000 Wh per day across two days needs at least 2,000 Wh of usable capacity. Lithium iron phosphate (LiFePO4) batteries are widely used in DIY builds because they tolerate many charge cycles. Most manufacturers specify usable capacity lower than nameplate capacity, so check the datasheet before buying.

Step 3: Size the Solar Panels and Charge Controller

Divide your daily watt-hour need by the peak sun hours at your location, then add losses. If you need 1,200 Wh per day and receive about 4 peak sun hours, you need roughly 300 W of panels, or about 400 W with a realistic loss factor. Use an MPPT charge controller rated for your battery voltage and for the panel array’s maximum input voltage and current.

Step 4: Choose an Inverter

The inverter converts battery DC power to 120 V AC. Its continuous rating must exceed the combined running wattage of everything you plug in at once. Pure sine wave inverters are the safer choice for electronics and motor loads like refrigerators and pumps. Pay attention to surge rating too, since motors draw several times their running watts on startup.

Step 5: Wire and Protect the System

Use wire gauge sized for the current and distance, and install fuses or breakers on the battery, between the controller and battery, and on the inverter input. Keep the battery in a ventilated, temperature-controlled space. Ground the system according to local electrical code.

Step 6: Connect Loads Safely

Never backfeed your home’s electrical panel through a standard outlet. Doing so can energize utility lines and injure line workers. Use a properly installed transfer switch or plug appliances directly into the inverter. If the work involves your main panel, hire a licensed electrician.

Tips and Common Mistakes

  • Sizing only by watts, not watt-hours. Runtime depends on energy, not power.
  • Ignoring motor startup surge when choosing the inverter.
  • Assuming full battery capacity is usable. Account for the depth-of-discharge limit.
  • Skipping fuses. A short circuit on a large battery can cause a fire.
  • Forgetting seasonal sunlight changes. Winter peak sun hours can be far lower than summer.
  • A clamp-style watt meter helps you measure real appliance draw rather than relying on label estimates. View on Amazon
  • A pure sine wave inverter protects sensitive electronics and motor loads. View on Amazon
  • An MPPT solar charge controller improves harvest from panels compared with basic PWM controllers. View on Amazon

For a comparison of ready-made options against a DIY build, see Best Solar Generators for Home Backup. If you are weighing wind as an addition, Wind Generator vs Solar Panels: Which Fits Your Home Backup Needs? covers the tradeoffs.

FAQ

How many solar panels do I need for a backup system?

It depends on your daily watt-hour use and your local peak sun hours. Divide daily energy need by peak sun hours, then add 20 to 30 percent for losses.

Can a DIY system run a refrigerator all night?

Yes, if the battery capacity covers the fridge’s daily watt-hours plus a buffer. Many refrigerators use a few hundred watt-hours per day.

Is a DIY solar backup generator safe to connect to my house?

Plugging into the house wiring without a proper transfer switch is dangerous. Consult a licensed electrician before connecting to your main panel.

Conclusion

A diy solar backup generator is achievable once you know your daily watt-hour needs. Size the battery, panels, controller and inverter in that order, and protect every connection. For wiring near your main electrical panel, consult a licensed electrician.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our solar generators for home backup & emergencies guides, checking product details against manufacturer specifications and owner feedback.