Updated November 2026
The jackery explorer 3000 pro power station can keep essential household loads running through a power outage, but only if you match its capacity to what you actually plug into it. This guide shows you how to estimate watt-hours for a refrigerator, a CPAP machine and a sump pump, then turn those numbers into a realistic runtime for your outage plan.
Step 1: List Your Critical Loads and Their Wattage
Start with the devices you truly need during an outage. Most appliances print their running wattage on a label, usually on the back or inside the door. If the label lists only amps, multiply amps by the voltage (120 V in the US) to get watts.
Shopping for one? See our guide: 6 Best Jackery Explorer 300 Portable Power Station Models for Home Backup (2026).
- Refrigerator: often 100 to 200 W while running, but it cycles on and off, so average use is far lower.
- CPAP machine: typically 30 to 60 W while running.
- Sump pump: usually 800 to 1,000 W while pumping, but only for short bursts.
Motor loads like pumps and refrigerators also need a startup surge, sometimes two to three times their running wattage for a moment. Check that the unit’s surge rating covers this.
Step 2: Convert Each Load to Daily Watt-Hours
Watt-hours are the number that matters for runtime. Use this formula:
Daily watt-hours = watts × hours of use per day
For a refrigerator, assume it runs about 8 to 10 hours per day, even when it is cycling. For a CPAP, multiply its wattage by your typical sleep hours. For a sump pump, estimate the minutes it actually runs during heavy rain and convert that to hours.
| Load | Running watts | Estimated hours per day | Approx. watt-hours per day |
|---|---|---|---|
| Refrigerator | 150 | 8 | 1,200 |
| CPAP machine | 45 | 8 | 360 |
| Sump pump | 900 | 1 | 900 |
These figures are illustrative. Your own devices will differ, so replace them with your label wattage and realistic usage.
Step 3: Estimate Runtime Against Battery Capacity
Add your daily watt-hours together, then divide the usable battery capacity by that total. Real-world runtime is always lower than the simple division because inverters lose some energy as heat and battery capacity is not fully usable at every charge level. Plan for roughly 80 to 85 percent efficiency as a conservative starting point.
- Add the daily watt-hours for every device you will run.
- Divide your battery capacity by that total to get a theoretical number of days or hours.
- Multiply by about 0.8 to account for losses.
- Compare the result with how long your local outages typically last.
Step 4: Plan Recharging for Long Outages
If your outage could stretch past a single charge, decide how you will refill the battery. Options include a vehicle charging cable run while the engine idles, or pairing the unit with solar panels sized to your daily load. Charging from a generator also works, but check the unit’s input limits first. Keep the unit ventilated and do not run gas equipment indoors.
Common Mistakes to Avoid
- Using nameplate maximum wattage instead of average daily watt-hours, which makes runtime look shorter than it is.
- Forgetting that a sump pump’s surge can exceed its rated running power.
- Assuming the battery delivers its full rated capacity every time.
- Connecting more devices than the inverter’s continuous output rating allows.
- Waiting until a storm to test the setup. Run a short test beforehand.
Recommended Gear
- A plug-in watt meter helps you measure real draw from a refrigerator or CPAP over a full day, which beats relying on label numbers. View on Amazon
- A heavy-duty extension cord rated for outdoor and power station use keeps connections safe when the unit sits away from the appliance. View on Amazon
FAQ
Can the jackery explorer 3000 pro power station run a whole house?
Usually not for a full home. It works best on a short list of critical loads like a refrigerator, lights, a CPAP and a sump pump. Larger electric heating or cooking loads would drain it quickly.
How do I know if my sump pump will start on the unit?
Check the pump’s startup or locked-rotor surge and compare it with the unit’s rated surge capacity. Consult the manufacturer’s specifications or a licensed electrician if the numbers are close.
Should I run a refrigerator on backup power all day?
You can, but a refrigerator is one of the biggest daily energy users. Keeping doors closed and running it only as needed stretches your watt-hours. For medical or food-safety decisions, consult a professional.
Conclusion
To size a jackery explorer 3000 pro power station for an outage, list your critical loads, convert them to daily watt-hours and divide your usable capacity by that total with a margin for losses. Test the setup before you need it. Review your numbers each season as your devices change.

