Updated November 2026
Building a solar powered generator means connecting a solar panel, a charge controller, a battery and an inverter so that sunlight becomes usable household power. Done right, you end up with a portable or semi-permanent unit that charges from the sun and runs your devices during an outage or off-grid trip. The steps below cover the parts, the sizing math and the wiring order.
Step 1: Calculate Your Daily Watt-Hour Needs
Start with the loads you want to run and how long each one runs per day. Multiply the wattage of each device by its daily hours of use to get watt-hours (Wh). A device drawing 60 watts for 5 hours uses 300 Wh. For a deeper walkthrough, see How to Size a Solar Generator: A Step-by-Step Worked Example. Add the totals, then add 20 to 30 percent for inverter and wiring losses.
Shopping for one? See our guide: 6 Best Solar Powered Generators for Home Backup Compared (2026).
Step 2: Choose the Battery, Inverter and Charge Controller
Your battery capacity should cover at least one full day of your calculated load. Lithium iron phosphate (LiFePO4) batteries are common in DIY builds because they tolerate many charge cycles. The inverter must handle your peak wattage, including the startup surge of motors such as a refrigerator compressor or sump pump. The charge controller regulates current from the panels into the battery; an MPPT controller usually harvests more energy than a PWM one. For a clear explanation of how these parts interact, read How Solar Generators Work: Battery, Inverter and Charge Controller Explained.
Step 3: Size and Mount the Solar Panels
Panel wattage should be large enough to recharge the battery within your available sun hours. A rough estimate: divide your daily watt-hour need by the average peak sun hours at your location, then add a margin for cloudy days. Mount panels facing the equator at an angle close to your latitude, and keep shade off them. Expect real output to fall short of the rated wattage because of heat, dust and angle.
Step 4: Wire the System in the Correct Order
- Mount the battery in a ventilated, dry location and confirm the battery’s voltage matches the inverter and controller.
- Connect the panels to the charge controller first, observing the maximum input voltage rating.
- Connect the charge controller to the battery, with a fuse or breaker close to the battery terminal.
- Connect the inverter to the battery last, with its own fuse, and only then plug in loads.
- Check polarity with a multimeter before closing any connection.
Wiring errors are the most common cause of damaged equipment, so consider having a licensed electrician review the installation, especially for any system tied into household wiring.
Common Mistakes to Avoid
- Sizing the battery for average use instead of your actual peak and surge loads.
- Using undersized wire, which causes voltage drop and heat.
- Skipping fuses or breakers between components.
- Ignoring the panel’s maximum voltage, which can destroy a controller.
- Assuming rated panel wattage equals usable output on cloudy or winter days.
Recommended Gear
A multimeter helps you verify voltage and polarity before every connection. View on Amazon
Inline fuses or a fuse holder rated for your battery’s current protect the wiring between components. View on Amazon
Solar panel mounting brackets keep the array angled correctly and secured against wind. View on Amazon
FAQ
Is it cheaper to build a solar generator or buy one?
Building can offer more control over capacity and parts, but it requires time, tools and electrical knowledge. Pre-built units are simpler to set up and usually include built-in safety protections.
How big a battery do I need for a refrigerator?
A typical refrigerator uses a few hundred watt-hours per day, but its startup surge is much higher than its running draw. Check the nameplate and your own usage data, then size the inverter for the surge.
Can I connect the system to my home electrical panel?
Connecting to household wiring requires a transfer switch and must follow local electrical codes. Consult a licensed electrician before attempting it.
Conclusion
A solar powered generator is built from a few well-matched parts: panels, a charge controller, a battery and an inverter. Calculate your watt-hour needs first, then size each component around them. Wire carefully, fuse every connection and verify the system before relying on it during an outage.

