Updated November 2026
A do it yourself solar generator is a battery, inverter and solar panel setup you assemble from separate components instead of buying a finished power station. Building one lets you size the system to your exact loads, such as a refrigerator, a CPAP machine or a sump pump, and choose each part yourself. This guide walks through the sizing math, the parts you need and the order of assembly.
Step 1: Size Your Load Before You Buy Anything
Start by listing every device you want to run during an outage and its wattage, which is usually printed on the label or the power adapter. Multiply each device’s running watts by the hours you expect to use it, then add the totals to get your daily watt-hour (Wh) requirement. A typical full-size refrigerator might draw around 100 to 200 watts while running, but it cycles on and off, so its average draw is lower. For a deeper walkthrough of the math, see Solar Generator Wattage Calculator: Add Up Your Devices.
Shopping for one? See our guide: 6 Best Solar Powered Generators for Home Backup Compared (2026).
Add a 20 to 30 percent margin to cover battery aging, inverter losses and cloudy days. Then check the surge rating for motor loads like sump pumps, because startup current can be several times the running wattage. Surge vs Continuous Power: What Your Solar Generator Can Actually Start explains why this matters.
Step 2: Choose Your Battery, Inverter and Panels
Pick a battery bank that stores at least your daily Wh requirement after accounting for depth of discharge. Lithium iron phosphate (LiFePO4) batteries are the common choice for home builds because they tolerate many charge cycles. Your inverter must handle both your continuous wattage and your surge demand, and it should produce a clean pure sine wave for sensitive electronics.
For panels, divide your daily Wh need by the peak sun hours in your area to estimate the array wattage you need. A rough rule is that real-world output is well below panel nameplate rating, so plan for losses. Check the charge controller rating against the panel voltage and current, since mismatches are a frequent cause of slow or failed charging. If charging seems sluggish once the system is running, Why Is My Solar Generator Charging Slowly? Causes and Fixes covers the usual culprits.
Step 3: Assemble and Wire the System
- Mount the panels with a tilt suited to your latitude, and secure them so wind cannot lift them.
- Connect panels to the charge controller first, following the manufacturer’s wiring diagram.
- Connect the charge controller to the battery bank, with a fuse or breaker sized close to the battery’s rated current.
- Connect the inverter directly to the battery terminals, using a fused, properly rated cable. Never connect it to the panels.
- Power up with all loads off, confirm voltages at each stage, then add loads one at a time.
Keep the battery in a ventilated spot away from heat sources, and use cables thick enough for the current they carry. Undersized wire is a common fire risk.
Common Mistakes to Avoid
- Sizing only for running watts and ignoring motor startup surge.
- Skipping fuses or breakers between the battery and the inverter.
- Mixing panel and battery voltages without checking charge controller compatibility.
- Assuming a rated Wh capacity is fully usable; inverter losses and depth-of-discharge limits reduce it.
- Connecting a home-built system to your house wiring without a licensed electrician and a proper transfer switch.
Recommended Gear
- A multimeter helps you verify panel, battery and output voltages at each stage of assembly. View on Amazon
- Properly rated DC fuses and a fuse holder protect the battery and cabling from overcurrent. View on Amazon
- Solar-rated MC4 connectors and cable make panel connections weatherproof and secure. View on Amazon
FAQ
Is a do it yourself solar generator cheaper than buying a finished unit?
It can be, but the answer depends on your component choices and how much time you want to spend on design and wiring. Finished units also include tested safety features that a home build has to replicate.
Can I power my whole house with a DIY system?
Most home builds are sized for essential loads, not the whole house. Connecting to house circuits requires a transfer switch and a licensed electrician.
How long does a DIY solar generator take to build?
A simple portable setup can be assembled in an afternoon, while a larger mounted system takes longer for panel mounting and permitting. Check local rules before installing anything permanent.
Conclusion
A do it yourself solar generator gives you control over capacity, surge handling and layout, provided you size it carefully and wire it correctly. Start with an accurate load list, then choose matching components. If you are unsure about electrical work, consult a licensed electrician before connecting anything to your home.

