Updated November 2026
Home solar generator systems keep essential appliances running when the grid goes down. This guide shows you how to total the watt-hours you need, match that number to a battery and panel setup, and avoid the sizing errors that leave people short during a multi-day outage.
Step 1: List the Loads You Actually Need
Start with the appliances you cannot go without. For most households that means a refrigerator, a CPAP machine, a sump pump, a few lights, phone charging and maybe a Wi-Fi router. Ignore the rest for now. Every extra load raises the battery size you need, so keep the list short.
Shopping for one? See our guide: 6 Best Solar Powered Generators for Home Backup Compared (2026).
Step 2: Calculate Daily Watt-Hours
Watt-hours (Wh) equal watts multiplied by hours of use. Check the label or manual for each device’s running wattage, then estimate how many hours per day it runs. Refrigerators cycle on and off, so a typical compressor fridge may average well under its rated wattage over 24 hours. A CPAP often draws roughly 30 to 60 watts for about 8 hours. Sump pumps draw a lot of power when running but only for short bursts, so estimate based on how often your basement fills.
| Load | Example Running Watts | Example Daily Hours | Approximate Daily Wh |
|---|---|---|---|
| CPAP machine | 40 W | 8 hrs | 320 Wh |
| Compressor refrigerator | Varies (cycles) | 24 hrs at average draw | Check the manufacturer’s stated daily kWh |
| Sump pump (1/3 HP) | About 800 W while running | 0.5 hrs | About 400 Wh |
| LED lights (5 bulbs) | 50 W total | 4 hrs | 200 Wh |
Add the daily totals, then add 20 percent for inverter losses and battery aging. Multiply by the number of backup days you want to cover, such as two or three.
Step 3: Match the Battery and Solar Input
Battery capacity in watt-hours tells you how much energy you can store. Solar input in watts tells you how fast you can recharge it. A system with a large battery but little panel capacity may take days to refill after cloudy weather. Check how many peak sun hours your location gets per day, then divide the battery’s usable Wh by that number to estimate the panel wattage you need for a full daily recharge.
Step 4: Check Inverter Output and Surge Ratings
Your inverter must handle the combined running load and the startup surge of motor-driven devices. Sump pumps and refrigerator compressors can briefly draw several times their running watts at startup. Look for a surge rating well above your largest motor’s starting draw. Also confirm whether the unit provides 120V, 240V, or both, since whole-home backup often needs 240V.
Common Mistakes
- Sizing only for running watts and ignoring startup surge from pumps and compressors.
- Forgetting that usable battery capacity is lower than the rated number because of inverter losses.
- Assuming full sunlight every day. Plan for at least one or two low-sun days.
- Plugging a 240V appliance into a 120V-only system.
- Running the system outdoors in rain or leaving it in a closed garage without ventilation.
Recommended Gear
- Kill-A-Watt P3 Electricity Usage Monitor: Measures the actual watts and daily kWh your appliances draw, so your sizing uses real numbers instead of guesses. View on Amazon
- Extension cords rated for outdoor use: Safely connect panels and devices in rain-prone or damp locations. View on Amazon
FAQ
How many watt-hours do I need for a fridge and CPAP for one night?
A CPAP at roughly 40 watts for 8 hours uses about 320 Wh, and a refrigerator’s share depends on its efficiency and how often it cycles. Check the manufacturer’s stated daily energy use for the fridge and add the two totals with a 20 percent buffer.
Can a home solar generator system run a sump pump?
Yes, if the inverter’s surge rating covers the pump’s startup draw and the battery holds enough energy for the expected run time. Pumps only run in short bursts, so their daily energy use is often modest.
Do I need a licensed electrician to connect a whole-home system?
Portable systems usually plug into outlets, but connecting a system to your home’s wiring or a transfer switch typically requires a licensed electrician and local permits. Consult a qualified professional before making any permanent connection.
Conclusion
A well-sized home solar generator system starts with an honest list of essential loads and their daily watt-hours. Add a safety margin, match the solar input to your sun exposure, and confirm the inverter handles startup surges. Use the steps above and you will have a clear target before you buy.
For more background, see Home Backup With a Solar Generator: What It Can Power and How to Connect Safely and Solar Power Backup System for Home: A Step-by-Step Sizing Guide (2026), or compare options in Portable Solar Generator vs Home Battery System.

