Updated November 2026
To build a solar power generator, you connect solar panels to a charge controller, store the energy in a battery, and convert it to household AC power with an inverter. This guide walks through sizing each part against what you need to run, then shows the wiring order and safety checks that matter most. The result is a portable or fixed system that can keep small loads running during an outage.
Step 1: Calculate Your Daily Watt-Hours
Start with the loads you want to power and how long you need them to run. Multiply each device’s wattage by its hours of use per day to get watt-hours (Wh). A typical refrigerator might draw around 100 to 150 watts while running and cycle on and off, so its real daily use is usually well below running wattage times 24. For a method you can follow line by line, see How to Measure Appliance Power Consumption for Solar Generator Sizing and How to Size a Solar Generator: A Step-by-Step Worked Example.
Shopping for one? See our guide: Jackery Solar Generator Home Power 3000: 4 Best Options Compared (2026).
Add a 20 to 30 percent margin to cover battery losses, inverter inefficiency and cloudy days.
Step 2: Choose and Size the Battery and Inverter
Battery capacity in watt-hours tells you how much energy you can store. Divide your daily Wh total by the usable depth of discharge your battery specifies to find the minimum capacity. Lithium iron phosphate (LiFePO4) batteries are common in these builds because they tolerate many charge cycles, though you should confirm the specific chemistry and cycle rating on the datasheet.
The inverter must handle your largest combined load. Check both continuous wattage and surge rating. Motors, such as those in a sump pump or well pump, can briefly draw several times their running watts at startup. Surge vs Continuous Power: What Your Solar Generator Can Actually Start explains how to check this before you buy parts.
Step 3: Size the Solar Panels
Panel wattage needs to replenish the battery within the time you have available, typically one sunny day. Divide your daily Wh by the peak sun hours for your location, then add losses for temperature, wiring and angle. A rough rule is to aim for panel wattage around 1.3 to 1.5 times your daily energy divided by average peak sun hours. Use local solar data for your area rather than general assumptions.
Step 4: Wire the System in the Correct Order
Follow this sequence to reduce the risk of damage or shock:
- Mount the panels securely and confirm the roof or ground structure can hold them.
- Connect the panels to the charge controller first, with the controller set to match your battery chemistry.
- Connect the charge controller to the battery, using a fuse or breaker close to the battery terminal.
- Connect the inverter directly to the battery through its own properly rated fuse.
- Connect your loads to the inverter output only after you have tested voltage and polarity with a meter.
Use wire gauge rated for the current you expect, and keep runs short to limit voltage drop.
Common Mistakes to Avoid
- Skipping the surge rating check, which often causes inverter shutdowns when a motor starts.
- Using undersized wire between the battery and inverter, where current is highest.
- Connecting panels directly to the battery without a charge controller.
- Ignoring temperature limits for charging lithium batteries, which can prevent charging in freezing conditions.
- Leaving out fuses or breakers, which are essential for protecting the battery and wiring.
Recommended Gear
- Portable power station with solar input: A built-in charge controller and inverter simplify a first build and suit owners who want to move the system. View on Amazon
- Digital multimeter: Checking voltage and polarity before connecting loads is one of the simplest ways to avoid wiring errors. View on Amazon
- Inline DC fuse holder: Protects the battery-to-inverter circuit, where fault current is highest. View on Amazon
FAQ
Can I build a solar power generator without a charge controller?
Technically, panels can connect directly to some batteries, but a charge controller prevents overcharging and protects the battery. Most builds should include one, matched to the battery chemistry and panel voltage.
How much solar power do I need to run a refrigerator?
It depends on the fridge’s energy use and your sun hours. Measure its daily watt-hours and size panels and battery from that number, using a 20 to 30 percent margin.
Should I hire an electrician for this project?
Connecting a system to your home’s electrical panel is work for a licensed electrician and local code inspection. Standalone builds still involve high battery current, so consult a qualified professional if you are unsure about any step.
Conclusion
Building a solar power generator comes down to matching panels, battery and inverter to your measured daily energy use and your largest motor load. Work through the sizing steps first, then wire the components in the safe order with proper fusing. Once running, check performance over a few sunny and cloudy days to confirm the system meets your needs.

