Updated November 2026
The Anker SOLIX F3800 home backup power kit is built to keep essential circuits running when the grid goes down. This guide shows you how to total the loads you actually need to power, compare that against the kit’s capacity, and estimate how many hours of backup you can expect. Most of the work is arithmetic, and it takes about fifteen minutes with a list of your appliances.
Step 1: List the Loads You Need During an Outage
Start with what you genuinely need, not everything in the house. Most households focus on a short list: a refrigerator, a CPAP machine, a sump pump, a few lights, a router, and phone charging. Write down each item, then find its wattage on the label or in the manual. If only amps are listed, multiply amps by the voltage (usually 120 V in the US) to get watts.
Shopping for one? See our guide: Anker SOLIX vs EcoFlow (2026): Which Is Better for Home Backup?.
Step 2: Convert Wattage to Daily Watt-Hours
Battery capacity is measured in watt-hours (Wh), so you need energy per day, not power at one moment. Use this formula for each device:
Daily Wh = Running watts × Hours used per day
Refrigerators cycle on and off, so their average draw is much lower than the nameplate rating. Many owners use a plug-in watt meter for a day to get a realistic figure. A typical CPAP runs for about 8 hours overnight at a modest draw. A sump pump only runs when water rises, so estimate its duty cycle honestly.
| Load | Typical running watts | Hours per day (example) | Daily Wh (example) |
|---|---|---|---|
| Refrigerator (average) | around 100 W | 24 (cycling) | about 1,200 Wh |
| CPAP machine | around 40 W | 8 | about 320 Wh |
| LED lights (5 fixtures) | around 50 W total | 4 | about 200 Wh |
| Wi-Fi router and modem | around 20 W | 24 | about 480 Wh |
These values are illustrative. Replace them with your own measured or labeled numbers.
Step 3: Match Your Daily Total to the Kit’s Capacity
Add your daily Wh figures together, then account for losses. Inverters and power conversion typically lose some energy, and manufacturers usually specify round-trip efficiency in their documentation. A practical rule is to divide the usable capacity by your daily total and then reduce the result by about 15 percent for inefficiency. Keep the battery’s usable range in mind too, since most lithium systems are not drained to zero.
If your loads exceed what the kit can supply, you have two choices: drop lower-priority circuits, or add capacity. Expandable battery modules are one way to extend runtime without replacing the whole system.
Step 4: Plan Recharging and Check Surge Demands
Backup runtime only matters if you can recharge. Grid charging is the simplest method, but solar input extends runtime over multi-day outages. Check the kit’s maximum input rating against your panels or your charging source so you know how quickly it refills.
Motors, such as sump pumps and refrigerator compressors, draw a brief surge when starting. Confirm that the kit’s rated output and surge capability cover your largest motor. Overloading the inverter can trigger shutdowns at the worst possible moment.
Common Mistakes
- Using nameplate wattage for the refrigerator instead of its real average draw.
- Forgetting that a CPAP or pump may run far longer than you expect during a multi-day outage.
- Ignoring inverter and conversion losses, which can shave a large share off the stated capacity.
- Connecting loads that were never meant to run from a battery, such as space heaters or electric dryers.
- Testing the system only once. Run a short test each season to confirm it still starts and transfers loads.
Recommended Gear
A plug-in watt meter helps you measure real consumption for your refrigerator and other appliances, which makes your daily Wh estimate far more accurate. View on Amazon
A transfer switch or a properly installed interlock lets you connect the kit to your home’s essential circuits safely, which should be done by a licensed electrician. View on Amazon
Related Reading
If you are still comparing options, see Anker SOLIX vs Jackery (2026): Which Is Better for Home Backup? for a head-to-head look at the two brands. For sizing a larger whole-home setup, Whole-Home Backup Power Solution: How to Size One for Outages (2026) walks through the same watt-hour math at a bigger scale. You can also review Home Backup With a Solar Generator: What It Can Power and How to Connect Safely before planning any solar input.
FAQ
How many hours will a refrigerator run on a backup kit?
It depends on the refrigerator’s average daily consumption and the kit’s usable capacity. Divide usable Wh by the fridge’s daily Wh, then reduce the result for inverter losses to get a realistic estimate.
Can the kit run a CPAP overnight?
In most cases, yes, because CPAP machines draw a modest amount of power. Calculate the device’s wattage multiplied by your sleep hours, then confirm the total fits comfortably within the usable capacity.
Should I have an electrician install the connection to my home?
Yes. Connecting a backup system to your home’s wiring requires proper isolation to protect utility workers and your equipment. Consult a licensed electrician before any permanent installation.
Conclusion
Sizing a home backup system comes down to listing your essential loads, converting them into daily watt-hours, and checking that total against the kit’s usable capacity with a reasonable efficiency margin. Measure your real appliance use where you can, since estimates often undershoot. Revisit the numbers whenever you add equipment or change your outage plan.

